What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Tools Workshop › Best Masonry Drill Bits: Types, Shanks and How to Pick
The short answer: the best masonry drill bits are carbide-tipped bits with a shank that matches your drill, a flute and tip design suited to the material, and a size that matches the anchor or fixing you plan to use. For occasional holes in brick or block with a standard drill, a straight-shank carbide-tipped bit used with hammer action is usually enough. For regular work in concrete, an SDS-style rotary hammer and matching SDS bits drill faster and with less effort. Dense stone, hardened concrete and reinforced slabs call for patience, sharp bits and sometimes a different tool altogether.
This guide does not rank brands or quote specifications for particular products. It explains the bit types, how shanks and tips differ, how to match a bit to the material and the fixing, what makes bits wear out, and how to keep dust and noise under control. Check current specifications and the instructions for your drill and your anchors before you buy.
Our Top Picks
DYRECELVE 12-Piece Masonry Drill Bit Set and Concrete5.51 x 2.95 x 0.64 inches0.45 PoundsCheck on Amazon
Contents
- How masonry bits actually cut
- Bit types compared
- Shanks and drill compatibility
- Matching bits to materials
- Sizing for anchors and fixings
- Drilling technique that saves bits
- Buyer checklist
- Mistakes to avoid
- Dust and drilling safety
- Frequently asked questions
- Bottom line
How masonry bits actually cut
A wood or metal bit slices material away. A masonry bit does something rougher. A hard insert at the tip, usually carbide, pulverises the material through a combination of rotation and, with the right drill, rapid hammering. The spiral flutes along the body then carry the powder up and out of the hole. That is why masonry bits look chunky compared with other bits, and why they clog and overheat quickly if the dust has nowhere to go.
Two things follow from this. First, the tip is where nearly all the work and wear happens, so the quality of the carbide and how well it is attached to the steel body are what separate a bit that lasts from one that dulls after a few holes. Second, the flutes matter more than they seem to. A bit that clears dust well cuts faster, runs cooler and is less likely to bind, so a bit with poorly formed flutes is a poor bargain whatever the tip looks like.
Bit types compared
The category covers several families of bits designed for different drills and different jobs. The table gives a general comparison. Always confirm what a particular bit is designed for before you use it.
| Bit type | Typical use | Drill needed | Main consideration |
|---|---|---|---|
| Straight-shank carbide-tipped | Brick, block, softer masonry, light concrete | Standard drill, ideally with hammer mode | Slower in hard concrete and can overheat if forced |
| SDS-style rotary hammer bit | Concrete, dense block, repeated or deeper holes | A rotary hammer with a matching chuck | Not compatible with a normal keyed or keyless chuck |
| Hex or quick-change shank bit | General masonry with impact drivers or quick-change chucks | Compatible driver or drill | Make sure the tool supports the hammering action you need |
| Diamond-tipped or diamond core bit | Porcelain, hard tile, stone, large round openings | Drill used per maker’s guidance, often with water cooling | Slower, and not the same as a hammering bit |
| Multi-material bit | Occasional mixed jobs on wood, tile, plastic and soft masonry | Standard drill | A compromise that usually wears faster in hard masonry |
Straight-shank carbide-tipped bits
These are the familiar bits for a household drill. They work well in brick, concrete block and softer mortar, particularly when the drill has a hammer setting. They will also go into concrete, but slowly, and pushing too hard in hard material just heats the tip and shortens its life.
SDS-style bits
SDS shanks have slots that let the bit slide back and forth in the chuck, which allows the hammering mechanism to strike the bit directly. This delivers far more impact than a standard drill can manage, so SDS bits are the sensible choice for frequent concrete drilling or deeper holes. They are made in several shank sizes, and the larger ones are for heavier tools, so match the shank to the tool.
Diamond and core bits
Diamond-tipped bits grind rather than hammer. They are the tool for hard, brittle materials like porcelain and dense stone, and for large openings such as pipes and vents. Many are intended to be used with water for cooling, and many should not be used in hammer mode, so follow the maker’s instructions closely.
Shanks and drill compatibility
It is easy to overlook the other end of the bit, but the shank decides whether a bit fits your tool at all and how well it transfers force.
- Round or straight shanks fit standard drill chucks and are the usual choice for light and medium work. Check that the shank diameter is within your chuck’s range.
- Hex shanks grip well in quick-release chucks and some impact drivers, but check whether the tool is suitable for drilling masonry.
- SDS-style shanks fit rotary hammers made for them. There are several variants, and they are not all interchangeable.
- Threaded or adapter shanks are used with some core bits and specialist systems, so check the thread and adapter match before buying.
Rotary hammer and hammer drill are not the same thing. A hammer drill uses a mechanism that taps the chuck forward while rotating, which is fine for brick and block and light concrete. A rotary hammer uses a piston to strike the bit with far greater force and is better suited to dense concrete and regular heavy work. If you plan to drill many holes in concrete, it may be more economical to use the right tool than to keep replacing bits in a weaker drill.
Matching bits to materials
Brick
Brick varies widely, from soft and crumbly to very hard and dense. A standard carbide-tipped bit with moderate pressure is normally suitable. Drill into the brick, not the mortar joints, where possible, as joints are weaker and may not hold a fixing well, and use a lower speed or switch off hammer mode on old or fragile brick to avoid cracking it.
Concrete block and cinder block
Blocks are often hollow or aerated, so the bit can suddenly break through into a void. Control your pressure when you feel the resistance drop. Hollow blocks usually need fixings designed for them, not ones intended for solid material.
Poured concrete
Concrete is where bit quality shows. Expect slower progress, more heat and faster wear than in brick. Hardened or older concrete is harder than fresh, and aggregate inside the mix can stall a bit unexpectedly. Rebar is the other hazard. If the bit stops and the drill starts to labour, you may have hit steel, and a standard masonry bit is not made to cut through it, so stop and reassess instead of forcing it.
Natural stone and pavers
Stone varies from soft to extremely hard. Sandstone and limestone are often within reach of a good carbide bit, while granite and dense engineered pavers may need diamond tooling. Use slow speeds, light pressure and breaks to cool the bit.
Tile and porcelain
Ordinary masonry bits can crack glazed tile and are poor at drilling porcelain. A bit made for tile or a diamond-tipped bit, run without hammer action, is a more suitable choice. Check the maker’s guidance for the material in front of you.
Sizing for anchors and fixings
Choose the bit to suit the fixing, not the other way round. Anchors, plugs and screws each come with instructions that specify the hole size and the depth. Drill to those figures, as a hole that is too big will not grip and a hole that is too small may split the masonry or damage the fixing.
- Read the instructions that came with the anchor, and choose the bit size and type they call for.
- Allow for dust at the bottom of the hole by drilling slightly deeper than the fixing length, if the instructions permit.
- Use a depth stop, a wrapped piece of tape or a marked bit so every hole is a consistent depth.
- Clean the hole before you insert the fixing. Dust left in the hole can reduce holding power, and some anchor systems explicitly require blowing out or brushing the hole.
- Do not enlarge a hole by wobbling the drill. A wobbled hole is oversized and weak.
For structural or safety-critical fixings, such as anything holding weight overhead or a heavy load on a wall, follow the anchor manufacturer’s current instructions to the letter and consider professional advice.
Drilling technique that saves bits
Good technique extends bit life more than almost any purchase decision.
- Mark and start gently. Begin at low speed without hammer action if the surface is smooth or fragile, so the tip bites instead of skating.
- Let the tool work. Apply steady, moderate pressure and let the bit do the cutting. Leaning hard overheats the tip and stresses the shank.
- Withdraw to clear dust. Pull the bit partly out while it is spinning to clear the flutes, then continue.
- Keep it straight. Hold the drill square to the surface. A side-load can jam or snap a bit.
- Pause to cool. A bit that is too hot to touch is a bit that is being damaged. Let it rest in the air, and do not quench a hot carbide tip in water.
- Stop when it stalls. If a hole stops progressing, check for rebar or a worn tip. A blunt bit that is forced harder just gets blunter.
For a tidy kit, a boxed assortment is often better value than singles, so you could compare masonry drill bit sets and check that the sizes cover the anchors you actually use. For serious concrete work, SDS-plus drill bits are worth a look if you own a compatible rotary hammer.
Buyer checklist
- Does the shank fit your drill, and is that drill suitable for masonry work?
- Is the tip carbide, or diamond for tile and stone, and is it well attached to the body?
- Are the flutes well formed so dust clears easily?
- Does the size range cover the plugs and anchors you plan to use?
- Is the length enough for the depth you need, plus extra for dust?
- Does the material you drill most often match what the bit is rated for?
- Is a case or organiser included so the bits stay sorted and undamaged?
- Have you read the current instructions for your drill about which bits and modes it supports?
- Do you need extras such as a depth stop, a dust shroud or a core bit adaptor, like a drill dust shroud?
Mistakes to avoid
- Using a wood or metal bit in masonry. It will blunt almost immediately and may overheat dangerously.
- Forcing the drill. More pressure does not make a bit cut faster once it is dull or hot.
- Ignoring the shank. A bit that does not fit your tool properly can slip, wobble or damage the chuck.
- Running hammer mode on tile or fragile material. It can crack tiles and crumble soft or old brick.
- Drilling into mortar and expecting a strong fixing. Joints are usually weaker than the brick or block around them.
- Picking the wrong size for the anchor. The anchor’s instructions, not guesswork, set the hole diameter.
- Leaving dust in the hole. It cuts holding power and can stop an anchor seating correctly.
- Drilling blind. Pipes, cables and rebar may be hidden behind or within the wall.
- Chasing a cheap price on thin carbide. A bit that chips or dulls early costs more in time than it saves.
- Skipping protection. Masonry dust is not something to breathe in.
Dust and drilling safety
Drilling into brick, block, concrete and stone releases fine dust that can be harmful to breathe, and some masonry dust contains silica, which is associated with serious lung disease after long or heavy exposure. Treat dust control as part of the job, not an optional extra.
- Control the dust at source. Use a dust shroud or a vacuum attachment where possible, or wet methods where the tool and material allow, and work outdoors or in ventilated spaces.
- Wear a suitable respirator. Choose protection that is rated for fine dust according to current guidance, and make sure it fits properly.
- Wear eye protection. Chips and fragments can leave the hole at speed, so safety glasses or goggles are essential.
- Protect your hearing. Hammer drills and rotary hammers are loud, particularly when working indoors.
- Check for hidden services. Locate cables, pipes and other hazards with a suitable detector and building plans before drilling into walls, floors and ceilings. If in doubt, switch off power at the source and seek advice.
- Secure the work and your stance. Use side handles when they are provided. A bit that binds can twist the tool in your hands with enough force to injure a wrist.
- Handle hot bits carefully. A bit can become hot enough to burn skin during drilling.
- Clean up safely. Use a vacuum made for fine dust or damp wiping, and avoid dry sweeping that sends dust back into the air.
If you are working on older buildings, ask whether materials might contain hazardous substances before cutting into them, and follow local rules for dust and waste.
Frequently asked questions
1. Can I drill concrete with a normal drill and a masonry bit?
You often can, using a carbide-tipped bit and hammer mode, but it will be slow and tiring for anything but a few holes. For regular concrete work, a rotary hammer with SDS-style bits is much more practical.
2. What is the difference between an SDS bit and a regular masonry bit?
The difference is mainly the shank. SDS shanks are designed for rotary hammers that strike the bit directly, while straight-shank bits fit ordinary chucks. The two are not interchangeable.
3. Should I use hammer mode for brick?
Often yes for hard brick and block, but not always. Old, soft or fragile brick may crack, so test on a low setting and follow your drill’s instructions.
4. Why does my bit stop cutting?
Common causes are a worn or overheated tip, clogged flutes, too little pressure or too much, and hitting rebar or hard aggregate. Pull the bit back to clear dust and check the tip.
5. Can masonry bits drill through rebar?
No, they are not designed to. If you hit steel, stop and consider moving the hole, or use a tool and bit made for cutting reinforcement after getting advice on the structure.
6. How do I choose the right size bit for an anchor?
Follow the instructions that come with the anchor, which specify the diameter and depth. Do not guess, and check the current instructions as they can vary between products.
7. Are multi-material bits any good?
They are convenient for occasional mixed jobs in soft masonry, tile and wood, but a dedicated masonry bit generally lasts longer and cuts better in hard material.
8. How can I reduce dust when drilling?
Use a dust shroud or vacuum attachment, work with ventilation, wear a suitable respirator and clean up with a vacuum designed for fine dust instead of sweeping.
Bottom line
Match the shank to your drill, the tip to your material and the size to your anchor, then protect your lungs, eyes and ears. A modest set of good carbide bits, used with patience and a clear dust plan, will outperform a larger set of cheap ones. Always check current specifications and instructions before buying, and when you are ready, you can browse carbide masonry bits and compare them against the checklist above.
Disclosure: As an Amazon Associate, we earn from qualifying purchases. Links marked as sponsored may earn us a commission at no extra cost to you.
Related guides
Worth a look next
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.


Write Your Review
No reviews yet. Be the first to share your experience!