What's inside
As an Amazon Associate I earn from qualifying purchases. This post may contain affiliate links at no extra cost to you.
Home › Tools Workshop › Best Jackhammers: Types, Sizes and Buying Advice
Our Top Picks
The Short Answer
The best jackhammer is the one sized to the concrete in front of you and powered by something you already have. For thick slabs, driveways and road-type work, a pneumatic paving breaker fed by a properly sized compressor is the traditional workhorse. For most home and light commercial jobs, a heavy electric breaker is simpler because it needs only a suitable outlet or generator. Anything much larger than that is usually a rental, not a purchase.
Do not choose by the biggest number on the box. Choose by weight class, power supply, vibration control and the bit style you will need, and plan your protective equipment and utility checks before the tool arrives.
In This Guide
- What a jackhammer does
- Types of jackhammers
- How to choose
- Features worth paying for
- Power, size and weight
- Technique and typical jobs
- Safety
- Maintenance
- Common mistakes
- Buy versus rent
- Checklist
- FAQ
- Conclusion
What a Jackhammer Does
A jackhammer is a heavy handheld breaker that drives a steel bit into hard material with repeated blows. The name comes from the way the tool pounds up and down on a fixed point. Concrete is strong when squeezed but weak when it is cracked and pried, so the bit does not need to grind the material away. It fractures it, and the operator lifts the pieces out.
People use “jackhammer” for pneumatic breakers most often, but the word also covers electric and hydraulic tools of similar size. What sets them apart from lighter demolition hammers is weight and energy: a jackhammer relies on its own mass and a long stroke to break thick slabs, not on the operator’s strength.
Types of Jackhammers
Pneumatic breakers
These run on compressed air. They have a simple body with few electrical parts, tolerate heavy continuous use and run cool. Their drawback is the supporting kit: a compressor with enough output, a hose of the right bore and clean, oiled air. Without that, the tool strikes weakly.
Electric breakers
A heavy electric breaker plugs into mains power or a generator. It is quieter than an air tool and needs no compressor, which suits indoor work and small sites. Sustained performance depends on a healthy supply, so undersized extension cords and weak generators are the usual cause of poor results.
Hydraulic breakers
Hydraulic units draw oil from a power pack or a machine. They deliver high energy for their weight and are common on professional crews. They also bring hoses, pressure and fluid hazards that need training, which is why most casual users hire them with support.
Gasoline-driven breakers
Some portable breakers use a small engine to power the striking mechanism directly. They are handy where there is no mains supply or compressor. Expect exhaust, noise and heavier maintenance, and never run them in an enclosed space because of carbon monoxide.
Cordless breakers
Battery models exist in the lighter end of the range. They suit short jobs in awkward places but are not intended to replace a full-size breaker for sustained slab work.
Comparison of jackhammer types
| Type | Needs | Best for | Watch out for |
|---|---|---|---|
| Pneumatic | Compressor, hose, air line oiler | Long sessions on thick concrete | Undersized compressor, hose whip |
| Electric | Mains power or generator | Indoor and small-site breaking | Voltage drop, cord damage |
| Hydraulic | Power pack or host machine | Professional, high-energy work | Pressurised fluid, training needs |
| Gasoline | Fuel, ventilation | Remote sites without power | Fumes, noise, upkeep |
| Cordless | Charged batteries | Short, light tasks | Limited sustained output |
How to Choose
Start with thickness and reinforcement. Thin, unreinforced paving can be broken with a mid-weight breaker. Thick slabs, mass concrete and heavily reinforced sections call for the heavy end, or for a different method altogether, such as sawing before breaking.
Next, count the hours. A tool that hits well but wears you out in thirty minutes will give you a slow job and a sore body. Heavier breakers actually reduce effort per blow because gravity does more of the work, but only if you can lift, position and lower them safely. Be honest about your strength and the footing you will have.
Then look at power. If you own a large compressor, a pneumatic breaker is cost-effective. If you do not, an electric breaker is usually cheaper to start with. Check the electrical rating of the circuit you will use, and avoid long thin cords. Finally, budget for bits, a hose or cord, hearing and eye protection, a respirator and a way to move the machine.
Comparison by weight class
| Class | Typical work | Handling | Common choice |
|---|---|---|---|
| Light | Tile, screed, paving slabs | One person, easy to carry | Homeowners, renovators |
| Medium | Garden slabs, footings, shed bases | Two hands, stable stance | Landscapers, builders |
| Heavy | Driveways, thick floors, road repairs | Needs strength and technique | Contractors, rental hire |
Features Worth Paying For
Vibration control. Handles that are isolated from the striking mechanism reduce the shock that reaches your hands. This is the single most meaningful comfort feature, because long-term vibration exposure can damage nerves and blood vessels.
Bit retention. A reliable latch or retainer keeps the bit in the tool when you lift it out of the cut. A loose bit can fall out or be thrown.
Throttle control. A progressive trigger or valve lets you start gently to seat the bit before going to full power. On pneumatic tools, a well-designed throttle also reduces sudden surges.
Muffling. Exhaust silencers and housing design lower noise somewhat. They do not remove the need for hearing protection.
Dust provisions. Water-feed or extraction attachments reduce the cloud of silica-bearing dust. Check whether the model supports them if you work in enclosed or populated areas.
Accessory compatibility. Bits come in several shank styles. Choose a tool whose bits are widely available, and confirm the chuck size before buying spares.
Power Source, Size and Weight Explained
Weight is a trade-off. A heavier machine breaks faster, but it demands more from the operator and more from the equipment used to move it. As a general principle, buy the lightest tool that can finish the job in a reasonable time. If a job needs more, rent.
For pneumatic tools, the key matching figure is air volume. A breaker consumes a certain flow, and the compressor must exceed it for the tool to hold pressure. If the compressor cannot keep up, the tool stutters and performance drops. Hose length and diameter matter too, since long narrow hoses lose pressure. Use the manufacturer’s recommended hose size and keep couplings secure with whip checks or safety clips.
For electric tools, watch the supply. A heavy breaker draws substantial current, so use a cord of the recommended gauge and as short as practical, plug into a protected circuit and avoid sharing the circuit with other loads. For generators, size them above the breaker’s rated input to cover start-up demand, and confirm that the generator can run a sensitive motor cleanly.
The bit also affects performance. A pointed bit concentrates energy and starts a fracture. A flat chisel or spade clears edges and removes thin layers. A clay spade or wide blade suits asphalt and soft material. Keep bits sharp and replace them when the tip mushrooms or cracks.
Technique and Typical Jobs
Begin by marking the area and planning the order of removal. Work from the edge inward, keeping the bit angled slightly so that the break lifts the slab rather than driving it down. Start a short distance back from the edge, which gives the piece somewhere to go.
Hold the tool upright, let it do the work and do not lean on it. If the bit sticks, release the trigger and free it; do not use the tool as a lever. Move the bit a hand’s width between strikes and break the slab into sections that you can lift out. Reinforcement mesh can be cut or bent out of the way once the concrete is cleared.
Typical jobs include removing driveways and paths, breaking out floors for new drainage, taking out footings and breaking trenches in paving. For driveways, break the surface into manageable sections and keep a skip or trailer close. Where drainage or pipes run beneath, stop earlier and finish with hand tools.
Safety
- Eyes and face: Wear impact-rated goggles. Fragments can travel a long way, and a face shield adds protection.
- Hearing: Jackhammers are among the loudest hand tools. Wear ear defenders or high-rated plugs every time, and keep other people well away.
- Respiratory: Breaking concrete releases respirable crystalline silica. Use a properly fitted respirator rated for fine dust, with water suppression or extraction where possible. A paper nuisance mask is not enough.
- Vibration: Limit trigger time, take regular breaks, keep hands warm and stop if you notice numbness or tingling.
- Utilities: Locate and mark buried cables, gas and water lines before you break ground. Use utility locating services and detectors, and treat unknown lines as live.
- Rebar and post-tension: Know what is in the slab. Post-tensioned slabs hold stored energy in cables, and cutting or breaking them can be extremely dangerous. If you suspect them, stop and seek professional advice.
- Body protection: Wear steel-toe boots, gloves, long sleeves and trousers. Use a back-friendly lifting technique, or a trolley or lifting aid, when moving the tool.
- Compressed air: Secure all hose connections, never point air at skin and depressurise the line before disconnecting.
- Exhaust and fuel: Never run gasoline tools in enclosed or poorly ventilated spaces.
- Older materials: Old surfaces, adhesives and coatings can contain asbestos or lead. Test before you disturb them.
Maintenance
Pneumatic tools need a few drops of the recommended air tool oil in the inlet before each use, or an inline oiler on the line. Drain the compressor tank regularly to avoid water in the system, and inspect hoses and fittings for cracks or leaks.
For electric breakers, inspect the cord and plug, clear dust from vents and check the brushes if the motor uses them. Grease the mechanism according to the manual. Using the wrong lubricant or skipping intervals shortens the life of the striking parts.
For every type, check the chuck and retainer for wear, store bits clean and dry, and replace mushroomed or cracked bits. Keep the tool in a dry case or on a rack, off the ground. Record any abnormal noises or loss of power, since these are early warnings.
Common Mistakes
- Underestimating how much compressor output the tool needs.
- Running a heavy electric breaker on a long, thin extension cord.
- Pushing down on the tool instead of letting its weight work.
- Starting in the centre of a slab instead of at an edge or crack.
- Skipping a utility search because the ground “looks clear.”
- Dry breaking indoors without dust control or respiratory protection.
- Continuing to use a mushroomed or cracked bit.
- Working for long periods without breaks, which compounds vibration exposure.
- Failing to plan where heavy rubble will go once it has been broken.
Buy Versus Rent
Rental suits one-off projects. A heavy breaker is expensive to buy, awkward to store and may sit unused for years. A hire shop typically supplies a serviced machine, bits and sometimes a compressor, and you return it when you finish. You can also choose a tool that is larger than you would ever buy.
Buying suits repeat users. If you do landscaping, small building works or regular demolition, ownership saves money and gives you flexibility. A mid-weight electric breaker is the most common sensible purchase because it needs no extra equipment.
Whichever route you choose, think about transport. Heavy breakers can exceed what one person can safely lift into a vehicle. Ask about delivery, ramps or lifting aids, and be ready to take a professional operator when the work is beyond your comfort.
Checklist
- Measure slab thickness and note any visible reinforcement.
- Pick the lightest weight class that can complete the job.
- Confirm the power source: compressor output, circuit rating or generator size.
- Check cords or hoses for the correct size and length.
- Obtain pointed and flat bits suitable for the tool.
- Arrange eye, hearing and silica-rated respiratory protection.
- Mark and verify buried services before starting.
- Plan a dust and water control method.
- Plan rubble removal and storage.
- Schedule breaks to limit vibration exposure.
FAQ
Is a jackhammer the same as a demolition hammer?
The terms overlap. Jackhammer usually refers to larger, heavier breakers, often air-powered, while demolition hammer usually means a lighter electric handheld tool. Both fracture hard materials with repeated blows.
What size compressor does a pneumatic jackhammer need?
It must deliver more air volume than the breaker consumes at the working pressure. The tool’s data plate or manual gives the figure; choose a compressor with margin above it.
Can I use an electric jackhammer on a generator?
Often yes, but the generator must have enough rated output and clean power. Check the tool’s input rating and leave headroom for start-up.
How thick a slab can a jackhammer break?
It depends on the tool weight class, the concrete strength and reinforcement. Heavier breakers cope with thicker slabs, but very thick or heavily reinforced sections may need a different approach.
How can I reduce dust?
Use water suppression or extraction attachments, work outdoors where possible and always wear a fitted respirator. Clean up with a suitable vacuum, not dry sweeping.
Do I need to check for utilities even on my own property?
Yes. Buried lines may not be where you expect, and records can be incomplete. Use a locating service or detector and consult plans.
How long should I use it before resting?
Use the vibration information supplied with the tool and take frequent breaks. Stop if you notice numbness, tingling or pain, and seek medical advice for persistent symptoms.
Is it safe to break post-tensioned concrete?
Not without professional guidance. Tensioned cables can fail violently when cut or damaged. If you suspect a post-tensioned slab, stop work and obtain engineering advice.
Conclusion
Choosing the best jackhammer means weighing slab thickness, power availability, your own strength and how often you will use the tool. Pneumatic machines suit sites with compressors, electric breakers suit most small projects, and hydraulic units belong to professionals. Prepare with the right protection, a proper utility search and a plan for the rubble, and you will work faster and more safely.
Ready to compare? Browse electric breakers, replacement bits, air hoses and fittings and protective gear for demolition work.
Disclosure: As an Amazon Associate, powertoolsoutlet.com earns from qualifying purchases at no extra cost to you.
Related guides
Worth a look next
- Best Plate Compactors: Types, Sizes and Buying Guide
- Best Manual Tile Cutters: Types, Features and Buying Tips
- Best Plumbing Snakes: Types, Sizes and Safe Use
- Best Rebar Cutters: Types, Capacity and Buying Tips
- Best Impact Socket Sets: What to Look for Before Buying
- Best Hole Saws: Types, Materials and How to Choose
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
A free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountFree shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.


Write Your Review
No reviews yet. Be the first to share your experience!